Why you need UeeVii CPE820?

UeeVii CPE820 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data in the air and realize point-to-point or point to multipoint interconnection over a long distance. The port speed is 1Gmpbs, and the network transmission speed can reach 1200Mbps. The working data link layer realizes the interconnection of LAN. The transmission distance can reach 3km. CPE820 video bridge transmission usually consists of two devices in AP and client mode. At the client (receiver), CPE is connected to the IP camera, and at the AP side (sender), CPE is connected to the video recorder. The AP can receive wireless data sent from multiple clients, and can easily and conveniently centrally manage remote devices.

5.8G Technology & 1200Mbps Transmission Speed

CPE820 Gigabit wireless WiFi bridge is a 5.8G Long Range WiFi Extender Outdoor CPE with a digital tube display. Point-to-point pairing can be done by dialing without having to access the GUI, avoiding the complex setup program, saving much human work and cost, and making the long-range wireless coverage, data transmission, and wireless monitoring simple and professional.
1000Mpbs digital display wireless bridge, transmission/receiver automatic networking, support point-to-point, point-to-multipoint, transmission/receiver flexible switching. WDS networking mode, video network dual compatible. The transmission speed between 2 bridges max is 1200Mbps. The highest network speed that can be achieved max is 1Gbps.

Built-in 16dBi & 3KM Working Distance

Point to point wireless bridge built-in 16dBi directional antenna, maximum 27dBm can automatically power adjustment to adapt to environmental changes, ensuring smooth video regardless of ultra-close distance, transmission distance up to 3km(Barrier-free), actual application distance should be less than 3KM.

Strong Anti-interference & High Speed Transmission,

1Gbps Wireless ethernet bridge conducted deep protocol optimization for wireless video surveillance transmission to ensure high-speed video transmission and smooth video surveillance, and the underlying wireless driver is optimized in-depth, using 5.8G IEEE 802.11ac single-band wireless transmission technology, with stronger anti-interference ability and better stability

Easy to Pairing

Outdoor wireless bridges adopting low power consumption and high-performance design, the RF index and radiation index are in full compliance with national standards. Supports dynamic MIMO power saving mode (DMPS) and automatic power-saving transmission (APSD), supports 24V POE power supply, is easy to install and deploy, simplifies construction, safe and reliable. Automatically re-pair when power is restored after a power outage.

Outdoor IP65 Weatherproof

CPE58G bridge IP65 weatherproof is very suitable for outdoor use, with rain, dust, and antifreeze.

Provide High-speed Video Monitoring

UeeVii CPE820 is widely used in expressway, reservoir and river monitoring, elevator monitoring system, on-site crane monitoring system, port and wharf monitoring system, marine aquaculture monitoring system, etc. The high-speed and smooth monitoring system makes life and work safer. Wireless is particularly important in large projects because wireless bridges can be quickly deployed and easily disassembled for reuse, and you don’t need to install new modems or pay a monthly fee, which saves you a lot of money.

UeeVii CPE820 Connect Your Online Life

Extend your house network to the second building, such as garages, barns, shops, and even neighbors, without having to layout network cables, saving costs.

More Details

Helpful Indicator Lights
Change the characters of the digital tube at the bottom of the wireless bridge to modify the pairing signal channel. The steady light state indicates that it is working, and the blinking state indicates that it is being set. The lights on the sideshow the power and LAN connection status, and the signal lights indicate the signal strength of the paired 2 bridges.

Only One 1Gbps Post
The wireless bridge has 1 100Mbps and 1000Mbps RJ45 ports, both of which can accept a 24V PoE power supply, recommended to use the 100M port for power supply, and the gigabit port is directly connected to the network, which will make the network speed better. And the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. The PoE adapter has a PoE port and a LAN port, and only the PoE port supplies power.

Switch Master-slave Bridge
Point wireless bridge switches the master and slave bridges through the A-B button, A represents the master bridge, and B represents the slave bridge. In point-to-multipoint, take one of the bridges as A, and the other bridges as B, and then set them to the same pairing character to complete the point-to-multipoint pairing.

Easy Installation
You can fix the point-to-point bridge on the bracket (ASIN: B09NLLG8MZ) with metal ties, or you can hang it on the wall; 2 wireless bridges are installed face to face as much as possible, with a clear view. It is recommended to purchase the UeeVii Universal Bridge Bracket.

How to Access and Setting the Wireless Bridge CPE Through Computer Access:

Step 1. Use a PoE adapter to power the wireless bridge through a network cable. Pay attention to the “PoE” and “LAN” ports marked on the PoE adapter, and power is supplied by POE instead of a DC power interface.
Step 2. Use a network cable to connect the CPE “LAN” port, connect the network cable other ends to the PoE Adapter “POE” port, use another network cable to connect to the “LAN” port of the PoE adapter, and connect the other end of the network cable to the computer’s “LAN” port.
Step 3. Find the number of the Wireless Bridge CPE digital display tube. For example, the number is 1 and the CEP is the A master bridge, then the IP of this CPE is 192.168.255.101; if the CPE is the B slave bridge, then the IP address of the CPE is 192.168.255.201.（There is a table corresponding to a number and IP in the manual）
Step 4. Very important step: Modify your computer’s IP address, change your computer’s IP address to 192.168.255.xxx(192.168.255.xxx cannot be the same as the IP of the CPE), make your computer’s IP and the bridge’s IP address be on the same network segment so that you can access them. Please refer to the manual to modify the computer IP address step or Google searches how to modify the computer IP address, it is very simple.
Step 5. After you modify your computer’s IP address, you open the computer browser and enter the IP address of the wireless bridge to access. For example, enter 192.168.255.101 to access.
Step 6. Enter the account password “admin/admin” to access, and set it after successful access.

Package Include:

2 * CPE820 Bridge
2 * POE Power Adapter (24V)
2 * Metal Hoop
1 * User Manual